AMS2 FFB settings

Fanatec Gran Turismo DD Pro

Base details in Hardware

Profile

Default+

Torque

8 Nm

Family

Direct drive

Confidence

High

Fanatec Gran Turismo DD Pro in Automobilista 2: Default+ profile, Gain 60, Low Force Boost 3, FX 32 and Damping 38.

In AMS2

Type

Default+

Gain

Low Force Boost

Damping

Menu Spring Strength

100

On the device

Fanatec Tuning Menu

SEN

Auto

100%

FFS

Linear

The AMS2 wiki uses Linear on the CSL DD, unlike the Podium DD1/DD2 (Peak).

NDP

22%

NFR

14%

NIN

10%

INT

2 - 4

FEI

FOR

100%

We only list what affects FFB in AMS2. Leave the rest of the software (FFB curve, equaliser, wheel presets, calibration) at its defaults.

Model notes

Same base as the CSL DD with PlayStation support: identical settings.
Keep LFB almost off on direct drive bases.
If the wheel oscillates on straights, increase damping before lowering Gain.

Every setting in Fanatec Tuning Menu

What each setting does, its range and what we set for AMS2. Anything without a value, leave at default.

Source: Official Tuning Menu FAQ

Main

SEN — Sensitivity

For AMS2AUTO

Degrees of rotation. On AUTO the game sets it.

Range: 90° – 2520° / AUTODef.: AUTO

FF — Force Feedback

Default

Maximum motor strength when the game sends FFB.

Model dependent: check the table above.

Range: 0 – 100%Def.: 100

FEI — Force Effect Intensity

For AMS280 – 100

Intensity and sharpness of effects: 0 is smoothest, 100 sharpest and most direct.

Range: 0 – 100Def.: 100

INT — FFB Interpolation

For AMS22 – 4

Smooths the game signal and raises its refresh rate. Higher = smoother.

Range: OFF, 1 – 20Def.: 6

LIN — FFB LinearityDD only

Default

Linearises the force response. DD bases only.

Range: ON / OFFDef.: OFF

Natural effects (DD only)

Generated by the BASE, not the game. In AMS2 keep them low.

NDP — Natural DamperDD only

Default

Damping that reacts to wheel acceleration and angle.

Model dependent: check the table above.

Range: OFF – 100Def.: 50

NFR — Natural FrictionDD only

For AMS20 – 3

Simulates the mechanical feel of steering components.

Range: OFF – 100Def.: OFF

NIN — Natural InertiaDD only

For AMS20 – 5

Simulates added weight on the steering axle. Useful with very light rims.

Range: OFF – 100Def.: OFF

DirectInput effects

Effects the game requests via DirectInput. AMS2 does not use them heavily: leave at 100 unless you want them off.

FOR — Force

For AMS2100%

Scales constant force effects.

Range: OFF, 010 – 120Def.: 100

SPR — Spring

Default

Scales the spring effect (pulls the wheel to the dynamic centre).

AMS2 barely uses it; the default (100) is harmless.

Range: OFF, 010 – 120Def.: 100

DPR — Damper

Default

Scales the damper effect requested by the game.

Range: OFF, 010 – 120Def.: 100

Wheel / pedals

SHO — Shock

Default

Rim rumble motors, if your wheel has them.

Range: OFF, 10 – 100%Def.: 100

BLI — Brake Level Indicator

Default

Vibrates when you reach the brake % you set.

Range: OFF – 100Def.: OFF

BRF — Brake Force

Default

Brake pedal curve (load cell).

Range: MIN – 50 – MAXDef.: 50

MPS — Multi Position Switch

Default

Mode for the rim multi-position switches.

Range: AUTO / Encoder / Constant / PulseDef.: AUTO

About this base

The same CSL DD hardware officially licensed for PlayStation (and the official base of Gran Turismo). 5 Nm peak, 8 Nm with the Boost Kit 180. The way into Direct Drive on PS5/PS4.

Wheelbases these settings are for

These settings are made for the models below. Open the sheet for full specs.

Fanatec Gran Turismo DD Pro

8 Nm

View sheet Buy at Fanatec See on Amazon

Purchase links are affiliate links: if you buy through them, Gonky Racing earns a commission at no extra cost to you.