Profile
Default+
Torque
6 Nm
Family
Belt
Confidence
Derived
Derived settings: there is no validated preset for this base, so we start from its family and torque recipe. An honest starting point, not dogma.
Fanatec CSL Elite Wheel Base V1.1 in Automobilista 2: Default+ profile, Gain 70, Low Force Boost 15, FX 35 and Damping 35.
In AMS2
Type
Default+
Gain
70
Low Force Boost
15
FX
35
Damping
35
Menu Spring Strength
100
On the device
Fanatec Tuning Menu
SEN
Auto
FF
100
DRI
Off / 1
SPR
0
DPR
0 - 20
Custom FFB profiles for this base
Community `ffb_custom_settings.txt` files that document settings for this specific base. They replace the FFB physics, not the in-game menu values.
Daniels Topspeed all-ine Custom File for all Bases 4-32Nm v1.5
rFuktor 5.0.1 - By Karsten with Shadak & Panos
| Car type | Gain | LFB | FX | Damping |
|---|---|---|---|---|
| Standard | 60% | 0% | 25-26% | 28% |
| Karts | 65% | 0% | 23% | 35% |
| Off-road | 52% | 0% | 28% | 35% |
| Street | 52% | 0% | 20% | 35% |
On the device
base/fanalab
- senAuto
- ffb90-100%
- dri-1 or 0
- fei60%-80%
- for100%
- sprOFF
- dprOFF
It goes in Documents/Automobilista 2 and replaces whatever you have. The Pilot Manager installs it for you and keeps a copy of yours.
Or let the Pilot Manager install it
Pick your base, it shows these same values and writes the file for you, keeping a copy of yours first so you can always go back.
Daniels Topspeed all-ine Custom File for all Bases 1-32Nm v1.7
rFuktor 5.0.1 - By Karsten with Shadak & Panos
| Car type | Gain | LFB | FX | Damping |
|---|---|---|---|---|
| Standard | 60% | 0% | 28% | 35% |
| Karts | 65% | 0% | 27% | 40% |
| Off-road | 52% | 0% | 33% | 40% |
| Street | 52% | 0% | 27% | 40% |
On the device
base/fanalab
- senAuto
- ffb90-100%
- dri-1 or 0
- fei60%-80%
- for100%
- sprOFF
- dprOFF
It goes in Documents/Automobilista 2 and replaces whatever you have. The Pilot Manager installs it for you and keeps a copy of yours.
Or let the Pilot Manager install it
Pick your base, it shows these same values and writes the file for you, keeping a copy of yours first so you can always go back.
Collection maintained by John B. Ellis · Download on OverTake
21 authors: Karsten Hvidberg · Shadak · Panos · Kuku · tUMi · NuScorpii · Joaquim Pereira · Reiza Studios · Alex291190 · Danielkart · Alegunner68 · Theodore Schultz · Manolo · Stakanov · Peter Stefani · TomP · NBrembo · Dmand · dud · Thirty-Four · Brock Harvey
Model notes
- Belt-driven Fanatec: in-game values close to a T300, device settings via the Tuning Menu.
- This is the safe all-rounder for GT and touring cars.
- Raise Gain only if the FFB meter is not clipping.
Every setting in Fanatec Tuning Menu
What each setting does, its range and what we set for AMS2. Anything without a value, leave at default.
Source: Official Tuning Menu FAQMain
SEN — Sensitivity
For AMS2AUTO
Degrees of rotation. On AUTO the game sets it.
FF — Force Feedback
Default
Maximum motor strength when the game sends FFB.
Model dependent: check the table above.
FEI — Force Effect Intensity
For AMS280 – 100
Intensity and sharpness of effects: 0 is smoothest, 100 sharpest and most direct.
INT — FFB Interpolation
For AMS22 – 4
Smooths the game signal and raises its refresh rate. Higher = smoother.
LIN — FFB LinearityDD only
Default
Linearises the force response. DD bases only.
Natural effects (DD only)
Generated by the BASE, not the game. In AMS2 keep them low.
NDP — Natural DamperDD only
Default
Damping that reacts to wheel acceleration and angle.
Model dependent: check the table above.
NFR — Natural FrictionDD only
For AMS20 – 3
Simulates the mechanical feel of steering components.
NIN — Natural InertiaDD only
For AMS20 – 5
Simulates added weight on the steering axle. Useful with very light rims.
DirectInput effects
Effects the game requests via DirectInput. AMS2 does not use them heavily: leave at 100 unless you want them off.
FOR — Force
For AMS2100%
Scales constant force effects.
SPR — Spring
Default
Scales the spring effect (pulls the wheel to the dynamic centre).
AMS2 barely uses it; the default (100) is harmless.
DPR — Damper
Default
Scales the damper effect requested by the game.
Wheel / pedals
SHO — Shock
Default
Rim rumble motors, if your wheel has them.
BLI — Brake Level Indicator
Default
Vibrates when you reach the brake % you set.
BRF — Brake Force
Default
Brake pedal curve (load cell).
MPS — Multi Position Switch
Default
Mode for the rim multi-position switches.
About this base
The CSL Elite Wheel Base V1.1: Fanatec's affordable belt-driven base (~6 Nm) that brought the ecosystem to a lower price; also offered in a PS4 version.
Wheelbases these settings are for
These settings are made for the models below. Open the sheet for full specs.
Fanatec CSL Elite Wheel Base V1.1
6 Nm
Purchase links are affiliate links: if you buy through them, Gonky Racing earns a commission at no extra cost to you.